Ara
Toplam kayıt 24, listelenen: 1-10
Selection of Tool Path and Parameter in Computer Aided Production of Belt Pattern Mold
(2015)
Bu çalışmada, deri kemer üzerinde bulunan 3 boyutlu sanatsal rölyef desenlerin oluşturulmasında kullanılan sıcak baskı kalıplarının üretiminde CNC takım yolu ve parametreleri araştırılmıştır. Kemer üzerinde baskı kalıplarıyla ...
Comparative study on the performance of different drive mechanisms used in a beta type Stirling engine through thermodynamic analysis
(2019)
In this study, thermodynamic and kinematic analyses of bell crank, slidercrank, rhombic and scotch yoke drive mechanisms were performed for a betatype Stirling engine with a swept volume of 365 cm3. The kinematic analysesof ...
A Decision Making Method By Combining Topsis And Grey Relation Method Under Fuzzy Soft Sets
(Yildiz Technical Univ, 2017)
In this study, we first introduce the fuzzy sets, soft sets, fuzzy soft sets and their related properties. We then present the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) that is one of classical ...
Investigation of corrosion pattern of AISI 316 and AISI 304 stainless steels in Na2B4O7 center dot 5H(2)O solution
(Vserossiiskaya Assotsiatsiya Korrozionistov, 2017)
The corrosion behaviour of AISI 316 and AISI 304 stainless steels in Na2B4O7 center dot 5H(2)O solutions with various concentrations (3%, 6% and 9% w/w) commonly used in wood industry was investigated by using electrochemical ...
The Effects of Humidity on Cast PA6G during Turning and Milling Machining
(Hindawi Ltd, 2017)
We compared the foundry PA6G samples in several dry and humid but different storage environments by processing them under the same cutting conditions such as progress rate (100, 120, 140, and 160 mm/min), cutting rate (90, ...
Subcarrier Allocation Algorithm Based on Greedy-Like in Multi Carrier Code Division Multiple Access Systems
(Kaunas Univ Technology, 2017)
One of the most important issues to be taken into consideration in multi carrier communication systems with multi users is the assignment of the available resources to the users efficiently. Thus, how to determine the ...
Prediction of Surface Roughness considering Cutting Parameters and Humidity Condition in End Milling of Polyamide Materials
(Hindawi Ltd, 2018)
To know the impact of processing parameters of PA6G under different humidity conditions is important as it is vulnerable to humidity up to 7 %. This study investigated the effect of cutting parameters to surface roughness ...
Effect of B4C Reinforcement Ratio and Sintering Temperature on the Mechanical Behavior in Al-B4C Composites
(Int Inst Science Sintering (I I S S), 2018)
In this study, powders of Al 1070 and B4C were prepared by volume in three different reinforcement ratios 4 % B4C, 8 % B4C and 16 % B4C compacted under the pressure of 500 MPa with cold pressing method then sintered under ...
The Effect of Fiberboard Modification on Adhesion Strength to Polyvinyl Chloride (PVC) Sheets or Eastern Beech (Fagus orientalis L.) Veneers
(North Carolina State Univ Dept Wood & Paper Sci, 2018)
The adhesion strength was evaluated for polyvinyl chloride (PVC) and Eastern beech (Fagus orientalis L.) veneers glued onto specially produced fiberboards using urea-formaldehyde (UF), polyvinyl acetate (PVAc), and ...
Half-space albedo problem for Inonu, linear and quadratic anisotropic scattering
(Korean Nuclear Soc, 2020)
This study is concerned with the investigation of the half-space albedo problem for "Inonu-linearquadratic anisotropic scattering" by the usage of Modified FN method. The method is based on Case's method. Therefore, Case's ...