Kategori "Makale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı" Makale Koleksiyonu İçin Listeleme
Toplam kayıt 81, listelenen: 21-40
-
The Effect of Solid Boriding Time on the Structure, Hardness and Corrosion Properties of AISI 5140 Steel
(MAIK NAUKA/INTERPERIODICA/SPRINGER, 2020)In this study, AISI 5140 steel samples were borided in an electrical furnace at a temperature of 950 degrees C for 4, 6 and 8 h. Structural examinations, hardness measurement and corrosion tests were performed to determine ... -
The effect of stacking sequence of carbon epoxy composite laminates on pinned-joint strength
(Elsevier Sci Ltd, 2003)In this paper, an experimental study regarding the determination of the safe as well as the maximum bearing strengths of a pinned-joint carbon epoxy composite laminate with [0degrees/45degrees/-45degrees/90degrees]s and ... -
Effects of alloy ratio and coating thickness on temperature distribution of thermal barrier coatings
(KOREAN ASSOC CRYSTAL GROWTH, INC, 2020)Pistons on internal combustion engines that are constantly subjected to high pressure and temperature should be light, resistant to heat, resistant to corrosion and have adequate hardness to work more efficiently and to ... -
Effects of equivalence ratio and CNG addition on engine performance and emissions in a dual sequential ignition engine
(SAGE PUBLICATIONS LTD, 2020)Compared to widening usage of CNG in commercial gasoline engines, insufficient but increasing number of studies have appeared in the open literature during last decades, while engine characteristics need to be quantified ... -
The effects of fine fire clay sanitaryware wastes on ceramic wall tiles
(Elsevier Sci Ltd, 2016)In the last decade, environmental preservation has become an important issue. Specifically, recycling of sanitaryware fine fire clay (FFC) waste is important for reducing costs. In this study, the use of FFC waste as an ... -
Effects Of The Boriding Process And Of Quenching And Tempering After Boriding On The Microstructure, Hardness And Wear Of AISI 5140 Steel
(WORLD SCIENTIFIC PUBL CO PTE LTD, 2020)An investigation was made on the effects of the boriding process and of quenching and tempering after boriding on the microstructure, hardness and wear of AISI 5140 steel. In this study, a new boriding agent (Baybora (R)-1) ... -
Energy and exergy analyses in a rotary burner with pre-calcinations in cement production
(Pergamon-Elsevier Science Ltd, 2004)Cement production facilities are often located in rural areas and close to quarries, where the raw materials required for cement production are present, i.e. limestone and shale. Although energy analysis, based on the first ... -
Energy And Exergy Analysis Of Piston Type Cng Compressors With Different Number Of Stages
(Parlar Scientific Publications (P S P), 2018)Nowadays, piston type compressors, having many advantages in compressing gases to high pressures, are preferred. In this study, energy and exergy analysis were performed by using the data obtained from the performance tests ... -
Estimation of solar potential in Turkey by artificial neural networks using meteorological and geographical data
(Pergamon-Elsevier Science Ltd, 2004)Turkey is located at the Mediterranean at 36degrees and 42degrees N latitudes and has a typical Mediterranean climate. The solar energy potential is very high in Turkey. The yearly average solar radiation is 3.6 kW h/m(2) ... -
Evaluation of flow behavior for clearance brush seals
(Asme-Amer Soc Mechanical Eng, 2008)The industrial applications of brush seals have been increasing due to their superior sealing performance. Advances in the understanding of seal behavior have been pushing the design limits to higher-pressure load, ... -
An experimental and numerical investigation of strength characteristics of carbon-epoxy pinned-joint plates
(Elsevier Sci Ltd, 2004)An experimental and numerical study has been carried out to investigate the strength of a pinned-joint carbon epoxy composite plate with [0degrees/45degrees/-45degrees/90degrees]s and [90degrees/45degrees/-45degrees/0degrees]s ... -
Experimental investigation of effects of single and mixed alternative fuels (gasoline, CNG, LPG, acetone, naphthalene, and boron derivatives) on a commercial i-DSI engine
(TAYLOR & FRANCIS INC, 2020)A commercial i-DSI (Intelligent-Dual Sequential Ignition) engine is tested to investigate performance and emissions for single fuels and alternative fuels mixed into gasoline. The novelty of the study is the first time ... -
Experimental modal analysis of curved composite beam with transverse open crack
(Academic Press Ltd- Elsevier Science Ltd, 2018)Curved composite beams are the most widely preferred structures due to their high strength, low weight, corrosion and heat resistance. The aim of this study is to examine the modalities and natural frequencies of curved ... -
Experimental robust optimal machining of hardened AISI 420 stainless steel with Al2O3+TiCN mixed ceramic tool
(Sage Publications Ltd, 2011)The high hardness and wear resistance levels of Alumina (Al2O3)-based ceramics make them excellent choices for incorporation into cutting tools that can be used to machine hardened steels. However, their poor fracture ... -
Experimental stress analysis of an arbitrary geometry containing irregularly shaped hole
(Wiley, 2019)Stresses can significantly influence the mechanical integrity of engineering structures. Motivated by prevalence of members containing cutouts, the objective of this paper is to demonstrate ability to stress analyse a ... -
Failure analysis of two-dimensional carbon-epoxy composite plate pinned joint
(Taylor & Francis Inc, 1999)The aim of this study is to investigate failure strength and failure mode of a mechanically fastened carbon-epoxy composite plate of arbitrary orientation. The failure load and the failure mode are analyzed numerically and ... -
Finite element simulation of chip flow in metal machining
(Pergamon-Elsevier Science Ltd, 2001)Finite element studies of machining are becoming ever more sophisticated. A basic approach which removes the need, in an elastic-plastic analysis, to follow the development of chip formation from initial contact between ... -
Flow Resistance Coefficients of Porous Brush Seal as a Function of Pressure Load
(Asme, 2018)Developments in brush seal analyses tools have been covering advanced flow and structural analyses since brush seals are applied at elevated pressure loads, temperatures, surface speeds, and transients. Brush seals have ... -
Influence of T5 heat treatment on the microstructure and lubricated wear behavior of ternary ZnAl40Cu2 and quaternary ZnAl40Cu2Si2.5 alloysEinfluss der T5 Warmebehandlung auf das Gefuge und das geschmierte Verschleissverhalten von der ternaren ZnAl40Cu2-und der quaternaren ZnAl40Cu2Si2,5-Legierung
(WILEY-V C H VERLAG GMBH, 2020)A ternary ZnAl40Cu2 and a quaternary ZnAl40Cu2Si2.5 alloys were produced by permanent mold casting and subjected to T5 heat treatment at a temperature of 150 degrees C for 24 hours. The structural, mechanical and lubricated ... -
Initial Results of Testing a Multilayer Laser Scanner in a Collision Avoidance System for Light Rail Vehicles
(Mdpi, 2018)This paper presents an application to detect and track obstacles using a multilayer laser scanner. The goal of the detection system is to develop collision avoidance for the Light Rail Vehicle (LRV). The laser scanner, ...