Erişim şekli için "info:eu-repo/semantics/closedAccess" Makale Koleksiyonu listeleme
Toplam kayıt 32, listelenen: 1-20
-
Addition of cement kiln dust in ceramic wall tile bodies
(Springer, 2019)The volume of wastes generated from heavy industries, such as cement and steel industries, is increasing, and the cost of landfill disposal grows daily. Economical and eco-friendly areas of recycle are being developed to ... -
Agro-waste shaped porous Al2O3/Ni composites: Corrosion resistance performance and artificial neural network modelling
(Elsevier Science Inc, 2018)In the present study, an analysis on the combined effect of nickel (Ni) reinforcement and pore former type in characterizing the corrosion behavior of composite porous alumina ceramics was performed. In order to showcase ... -
Development of lightweight ceramic construction materials based on fly ash
(Australian Ceramic Society, 2017)This study aims to demonstrate the suitability of using lightweight ceramics as a construction material in preference to autoclaved aerated concrete and pumice blocks or the more commonly used brick. For construction ... -
The development of porcelain foams lighter than water for heat isolation application
(Springer, 2019)In this study, technological and heat isolation properties of porous ultra-lightweight porcelain foams were investigated. Traditional construction materials such as brick show good durability against environmental conditions. ... -
Development of porous lightweight clay bricks using a replication method
(Australian Ceramic Society, 2018)This study focused on porous lightweight clay bricks as a construction material as opposed to autoclaved aerated concrete and pumice blocks. Traditional clay bricks exhibit good stability against environmental conditions ... -
Effect of Aging Treatment on Surface Roughness, Mechanical Properties, and Fracture Behavior of 6XXX and 7XXX Aluminum Alloys
(Springer, 2014)The effect of aging treatment on the surface roughness and mechanical properties of AA6061 and AA7075 alloys was studied. Microhardness and tensile tests were used to investigae the mechanical properties. X-ray diffraction ... -
The effect of cement raw mix waste dust on porcelain tile properties
(Springer, 2019)Nowadays, the recycling of industrial waste is one of the priority issues. Recycling studies related with reducing the negative effects of wastes on the environment are becoming increasingly important. It was believed that ... -
Effect of matrix temperature and powder size on the infiltration height of SiO2-reinforced Al 7075 matrix composites produced by vacuum infiltration
(Walter De Gruyter Gmbh, 2017)In this study, the effect powder size and matrix temperature on the physical and mechanical properties of SiO2-reinforced Al 7075 matrix composites were investigated. It was observed that with increasing powder size and ... -
The Effect of Nepheline Syenite Addition on the Sintering Behaviour of Sanitaryware Bodies
(Australian Ceramic Society, 2016)In this study, the effect of nepheline syenite addition on the sintering and material properties of sanitaryware porcelain bodies was investigated. Three ceramic sanitaryware bodies were prepared by substituting Na feldspar ... -
Effect of Reinforcement Volume Ratio on Thermal Conductivity of SiO2 Reinforced Al Matrix Composite Produced by Vacuum Infiltration Method
(Asian Journal Of Chemistry, 2010)In this study, SiO2 powders with 105 mu m particle size were filled in quartz tubes freely to form 30, 40, 50% reinforcement volume ratios. Liquid A17075 alloy was vacuum infiltrated into the SiO2 compact under the same ... -
Effect of spodumene addition on pyroplastic deformation of porcelain stoneware
(Korean Assoc Crystal Growth, Inc, 2014)Lithium aluminosilicates, such as spodumene, have been used as raw materials in the production of thermal shock resistant whiteware and sanitaryware. The presence of spodumene causes enhancement of mullitization and imparts ... -
Effects of Alumina on Porcelain Insulators
(Australian Ceramic Society, 2016)This study was conducted under both industrial and laboratory conditions for improving material properties (i.e. mechanical and electrical) of electroporcelain bodies produced by porcelain insulator factories in Turkey. ... -
Effects of reinforcement volume fraction on the abrasive wear behaviour of Al-MgO composites produced by the vacuum infiltration method
(Sage Publications Ltd, 2011)In this study, the effects of the reinforcement volume fraction on the abrasive wear behaviour of reinforced MgO composites produced by the vacuum infiltration method with 5, 10, and 15 vol% of the volume fraction of Al ... -
Effects Of Sintering, Ageing And Cryogenic Treatments On Structural And Mechanical Properties Of Aa2014-B4c Composite
(Gazi Univ, Fac Engineering Architecture, 2013)In this study, powders of gas atomized AA2014 and solid B4C were mixed and then used in an infiltration system. To attain particulate reinforced aluminum composites, fine particles of B4C were added in right proportions ... -
Effects Of The Boriding Process And Of Quenching And Tempering After Boriding On The Microstructure, Hardness And Wear Of AISI 5140 Steel
(WORLD SCIENTIFIC PUBL CO PTE LTD, 2020)An investigation was made on the effects of the boriding process and of quenching and tempering after boriding on the microstructure, hardness and wear of AISI 5140 steel. In this study, a new boriding agent (Baybora (R)-1) ... -
Impact of different isothermal aging conditions on the IMC layer growth and shear strength of MWCNT-reinforced Sn-5Sb solder composites on Cu substrate
(Elsevier Science Sa, 2019)In this study, the effect of multi-walled carbon nanotubes (MWCNTs) reinforcement on the intermetallic compound (IMC) layer growth and shear strength of Sn-5Sb-xCNT/Cu composite solder joints subjected to different isothermal ... -
Investigating the effect of porosity level and pore former type on the mechanical and corrosion resistance properties of agro-waste shaped porous alumina ceramics
(Elsevier Sci Ltd, 2017)The strength integrity and chemical stability of porous alumina ceramics operating under extreme service conditions are of major importance in understanding their service behavior if they are to stand the test of time. In ... -
Investigation of abrasion in Al-MgO metal matrix composites
(Pergamon-Elsevier Science Ltd, 2014)In this study, the effects of reinforcement volume fractions on abrasive wear behavior were examined in Al-MgO reinforced metal matrix composites of 5%, 10% and 15% reinforcement - volume ratios produced by melt-stirring. ... -
An Investigation of Abrasive Wear Behaviour of Al 2014-SiC Composites
(Walter De Gruyter Gmbh, 2015)In this study, the effects of SiC reinforcement volume fractions on hardness, porosity and abrasive wear behaviour were examined in Al 2014-SiC (<92.3 mu m) reinforced metal matrix composites (MMCs) of 3%, 6% and 12% ...