Yazar "Pul, Muharrem" için listeleme
-
7075, 6061 Ve 2024 Alüminyum Alaşımlarının Tornalanmasında 00V. Yüzey Pürüzlülugü ve Takım Aşınmasının Karşılaştırılması
Pul, Muharrem (2017)Alüminyum ve alaşımları hafifliği yanı sıra sağlamlığı ve kolay şekillendirilebilme özellikleri sayesinde endüstride giderek artan kullanım alanına sahip olmuştur. Bu alaşımlar içerisinde 7075, 6061 ve 2024 kalite aluminyum ... -
Al 1070 matrisli, bor karbür (B4C) takviyeli kompozitlerin toz metalurjisi ile üretilerek, aşınma dayanımı ve mekanik özelliklerinin incelenmesi
Pul, Muharrem; Kırıkkale Üniversitesi, Rektörlük, Projeler (KırıkkaleKırıkkale Üniversitesi, 2016)… -
Al1070/TiB2 Kompozitlerin Tornalanmasında TiB2 Takviye Miktarının Esas Kesme Kuvveti Ve Yüzey Pürüzlülüğüne Etkisi
Pul, Muharrem (2020)Bu çalışmada Al1070 matrisli TiB2takviyeli kompozitin işlenebilirliği incelenmiştir. İlk aşamada ağırlıkça %2, %4 ve %8 TiB2 takviyeli Al1070 kompozitler üretilmiştir. Daha sonra; kuru kesme şartlarında, 1 mm sabit kesme ... -
Alüminyum 7075 Matrisli Kompozitlerde SiC, B 4 C Ve TiB 2 Takviye Elemanlarının Mekanik Özelliklere Etkilerinin Karşılaştırılması
Pul, Muharrem (2019)Bu çalışmada toz metalurjisi yöntemi kullanılarak Al 7075 matris malzemesi içerisine SiC, B 4 C ve TiB 2 takviyeelemanları ayrı ayrı ilave edilmiştir. SiC, B 4 C ve TiB2 takviye ağırlık oranları %5, %10 ve %20 olarakuygulanmıştır. ... -
Balistik malzeme üretimine yönelik B4C+SiC takviyeli Al 7075 kompozitlerde optimum katkı oranının belirlenmesi
Baydaroğlu, Volkan (Kırıkkale Üniversitesi, 2018)Bu çalışmada SiC (silisyum karbür) ve B4C (bor karbür) takviyeli Al 7075 esaslı kompozitler, toz metalurjisi yöntemi kullanılarak, %40, %20 ve %10 takviye oranlarında üretilmiştir.Üretimi yapılan numuneler modellenerek ... -
Düşük takviyeli MgO-Al kompozitlerin vakumlu infiltrasyonunda takviye oranının infiltrasyon davranışına etkisi
Pul, Muharrem; Çalın, Recep; Çıtak, Ramazan; Şeker, Ulvi (2009)Bu çalışmada 149 µm parçacık büyüklüğündeki MgO tozları % 5, 10, 15 takviye-hacim oranı oluşturacak şekilde çelik tüp içersine serbest halde yerleştirilmiştir. Farklı sıcaklıklarda 550 mmHg vakum ve 5 dakika süre ile %5 ... -
Effect of B4C Reinforcement Ratio and Sintering Temperature on the Mechanical Behavior in Al-B4C Composites
Pul, Muharrem (Int Inst Science Sintering (I I S S), 2018)In this study, powders of Al 1070 and B4C were prepared by volume in three different reinforcement ratios 4 % B4C, 8 % B4C and 16 % B4C compacted under the pressure of 500 MPa with cold pressing method then sintered under ... -
Effect of matrix temperature and powder size on the infiltration height of SiO2 -reinforced Al 7075 matrix composites produced by vacuum infiltration
Calin, Recep; Pul, Muharrem; Citak, Ramazan; Seker, Ulvi (Adcotec Ltd, 2011)In this study, Al-MgO metal matrix composites (MMC) were produced with 5 %, 10 % and 15 % reinforcement-volume (R-V) ratios by the melt stirring method. In the production of composites 99.5 % pure Al was used as the matrix ... -
Effect of matrix temperature and powder size on the infiltration height of SiO2-reinforced Al 7075 matrix composites produced by vacuum infiltration
Calin, Recep; Pul, Muharrem; Bican, Osman; Kucukturk, Gokhan (Walter De Gruyter Gmbh, 2017)In this study, the effect powder size and matrix temperature on the physical and mechanical properties of SiO2-reinforced Al 7075 matrix composites were investigated. It was observed that with increasing powder size and ... -
The Effect of Reinforcement Volume Ratio on Porosity and Thermal Conductivity in Al-Mgo Composites
Çalın, Recep; Pul, Muharrem; Pehlivanli, Zuhtu Onur (Univ Fed Sao Carlos, Dept Engenharia Materials, 2012)In this study, the effects of reinforcement volume ratios (RVR) on composite structure and thermal conductivity were examined in Al-MgO reinforced metal matrix composites (MMCs) of 5%, 10% and 15% RVR produced by melt ... -
Effect of sintering on mechanical property of SiC/B4C reinforced aluminum
Pul, Muharrem (Iop Publishing Ltd, 2019)In this study, SiC (silicon carbide) and B4C (boron carbide) added Al 7075 based composites were prepared at 40%, 20% and 10% reinforcement ratios. Using powder metallurgy, composite sample with 9 different structures were ... -
Effect of sintering temperature on pore ratio and mechanical properties of composite structure in nano graphene reinforced ZA27 based composites
Pul, Muharrem (SPRINGER, 2020)Nano graphene platelet (Gr) reinforced nano composites with a zinc-aluminum alloy (ZA27) matrix were produced by powder metallurgy at four different mass ratios (0.5wt%, 1.0wt%, 2.0wt% and 4.0wt%) and three different ... -
Farklı Yöntemler ile Üretilen MgO Takviyeli Alüminyum Kompozitlerde Mekanik Davranışların Karşılaştırılması
Pul, Muharrem (2019)Bu deneysel çalışmada vakumlu infiltrasyon, karıştırmalı döküm ve toz metalurjisi teknikleriyle üretilmişolan MgO parçacık takviyeli alüminyum kompozitlerin mekanik davranışları karşılaştırılmıştır. Buamaçla daha önce üç ... -
Havcılık ve savunma sanayinde kullanılan A1 6061 T6 alüminyum alaşımının tornalanmasında yüzey pürüzlülüğü ve takım aşınmasının incelenmesi
Pul, Muharrem; Kırıkkale Üniversitesi, Rektörlük, Projeler (KırıkkaleKırıkkale Üniversitesi, 2017)… -
Investigation of cutting tool wear behaviors in machining of silicon carbide and magnesium oxide reinforced aluminum 2024 matrix composites
Pul, Muharrem (Iop Publishing Ltd, 2019)In this study, first Silicon Carbide (SiC) and Magnesium Oxide (MgO) powders of <= 105 micron particle size were mixed in equal amounts. Then, the powder mixture was reinforced by using vortex method in liquid Al2024 ... -
Investigation of effects of MgO ratio on the surface quality and tool wear in turning Al-MgO composites
Pul, Muharrem (Sage Publications Ltd, 2018)In this study, specimens of Al-MgO metal matrix composites with reinforcement-volume ratios of 5%, 10% and 15% were produced using vacuum infiltration method. The produced specimens were then tested for machining on computer ... -
Investigation of machinability in Al-MgO composites produced by melt-stirring
Pul, Muharrem; Uzun, Gultekin; Çalın, Recep; Seker, Ulvi (Walter De Gruyter Gmbh, 2013)In this study, Al-MgO reinforced metal matrix composites of 5%, 10% and 15% reinforcement-volume ratios were produced by melt-stirring and subjected to machining tests by carbide and coated carbide cutting tools. Machining ... -
Investigation of Mechanical Properties of B4C / SiC Additive Aluminum Based Composites and Modeling of Their Ballistic Performances
Pul, Muharrem; Baydaroglu, Volkan (Gazi Univ, 2020)In this study, 7075 grade aluminum-based composites reinforced with SiC (silicon carbide) and B4C (boron carbide) were produced with powder metallurgy at 40%, 20% and 10% reinforcement ratios. The mechanical properties of ... -
An investigation of surface quality of turning in al matrix mgo reinforced composite material
Pul, Muharrem; Çalın, Recep; Citak, Ramazan; Seker, Ulvi (Gazi Univ, Fac Engineering Architecture, 2011)In this study; Al/MgO composites having 5 %, 10 %, 15 % volume fraction of reinforcement are produced by vacuum infiltration method and microstructure of composites are determined. Produced materials of metal matrix composite ... -
Investigation of the tool wear, surface roughness, and chip formation in the machining of ZrO2-reinforced aluminum composites
Pul, Muharrem (SPRINGER HEIDELBERG, 2020)The aim of this study is to reveal how ZrO2(zirconia) contributes to the machinability of aluminum 1050. In the first stage of this study, composite materials were produced by the vortex method by adding different amounts ...