Yazar "Erdem, Umit" seçeneğine göre listele
Listeleniyor 1 - 20 / 28
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Change in transition balance between durable tetragonal phase and stress-induced phase of cobalt surface-layered in Bi-2212 materials by semi-empirical mechanical models(Iop Publishing Ltd, 2023) Erdem, Umit; Yildirim, Gurcan; Turkoz, Mustafa Burak; Ulgen, Asaf Tolga; Mercan, AliThis study has indicated the positive effect of sintering temperature on the mechanical durability, strength, critical stress, deformation degrees, durable tetragonal phase, failure and fracture by fatigue, and mechanical characteristic behavior to the applied test loads for the Co surface-layered Bi-2212 ceramic materials produced by the standard solid-state reaction method. The sintering mechanism has been used as the driving force for the penetration of cobalt ions in the Bi-2212 ceramic matrix. The microindentation hardness test measurements have been performed at the load intervals 0.245 N-2.940 N. The experimental findings have also been examined by the six different semi-empirical mechanical and indentation-induced cracking models. It has been found that all the mechanical performance parameters are improved considerably with increasing the diffusion sintering temperature up to 650 degrees C. On this basis, the Co surface-layered Bi-2212 sample produced at the sintering temperature of 650 degrees C has been observed to improve dramatically the mechanical durability and resistance to the applied test loads as a consequence of the formation of new force barrier regions, surface residual compressive stress regions, and slip systems in the Bi-2212 ceramic system. Similarly, the optimum sintering temperature has extensively enhanced the elastic recovery mechanism, critical stress values, and deformation degree levels, stored internal strain, and crack surface energy through the Bi-2212 ceramic materials. Accordingly, it has been noted that the best sample produced at 650 degrees C is more hardly broken than the other ceramics. Namely, the optimum sintering temperature has decreased the sensitivity to the applied test loads as a result of delaying the beginning of the plateau limit regions. On the other hand, all the mechanism has been found to reverse completely depending on the excess sintering temperature. Lastly, the indentation-induced cracking model has been found to exhibit the closest results to the original Vickers microhardness parameters in the plateau limit regions.Öğe Contribution of vanadium particles to thermal movement of correlated two-dimensional pancake Abrikosov vortices in Bi-2223 superconducting system(Elsevier, 2023) Ulgen, Asaf Tolga; Erdem, Umit; Yildirim, Gurcan; Turkoz, Mustafa Burak; Turgay, TahsinThis article breaks new ground in understanding of variation in the magnetic strength performance, flux pinning and energy dissipation mechanism of polycrystalline bulk Bi1.8Sr2.0Ca2.2Cu3.0Oy (Bi-2223) superconducting materials added with the different vanadium concentration level (0.0 <= x <= 0.30) under the magnetic field strengths applied up to 5 T for the first time. We provide the sophisticated and phenomenological discussions on the magnetoresistivity measurement results in three main sections along the paper. All the findings show that the increase of both the vanadium concentration in the crystal structure and external magnetic field strength damages significantly the magnetic strength performance, vortex dynamics, flux pinning ability and vortex lattice elasticity of bulk Bi-2223 superconducting ceramics. The vanadium addition promotes thermally the movement of correlated two-dimensional (2D) pancake Abrikosov vortices between the in-plane Cu-O-2 layers in the valance band, vortex lattice elasticity, vortex dynamics, distance for interlayer Josephson couplings and flux pinning centers and the theoretical computations confirm the remarkable degradation in the formation of super-electrons in the Bi-2223 crystal system. Thus, the vanadium addition is anticipated to be one of the best selectable materials to examine the differentiation in the thermal movement of correlated 2D Pancake Abrikosov vortices in the bulk Bi-2223 superconducting system. (c) 2022 The Author(s). Published by Elsevier Espana, S.L.U. on behalf of SECV. This is anopen access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/ by-nc-nd/4.0/).Öğe Dentinal tubule occluding capability of nano-hydroxyapatite; The in-vitro evaluation(Wiley, 2018) Baglar, Serdar; Erdem, Umit; Dogan, Mustafa; Turkoz, MustafaIn this in-vitro study, the effectiveness of experimental pure nano-hydroxyapatite (nHAP) and 1%, 2%, and 3% F doped nano-HAp on dentine tubule occlusion was investigated. And also, the cytotoxicity of materials used in the experiment was evaluated. Nano-HAp types were synthesized by the precipitation method. Forty dentin specimens were randomly divided into five groups of; 1no treatment (control), 2specimens treated with 10% pure nano-HAp and 3, 4, 5 specimens treated with 1%, 2%, and 3% F(-)doped 10% nano-HAp, respectively. To evaluate the effectiveness of the materials used; pH, FTIR, and scanning electron microscopy evaluations were performed before and after degredation in simulated body fluid. To determine cytotoxicity of the materials, MTT assay was performed. Statistical evaluations were performed with F and t tests. All of the nano-HAp materials used in this study built up an effective covering layer on the dentin surfaces even with plugs in tubules. It was found that this layer had also a resistance to degradation. None of the evaluated nano-HAp types were have toxicity. Fluoride doping showed a positive effect on physical and chemical stability until a critical value of 1% F-. The all evaluated nano-HAp types may be effectively used in dentin hypersensitivity treatment. The formed nano-HAp layers were seem to resistant to hydrolic deletion. The pure and 1% F(-)doped nano-HAp showed the highest biocompatibility thus it was assessed that pure and 1% F(-)doped materials may be used as an active ingredient in dentin hypersensitivity agents.Öğe Development of modulation, pairing mechanism, and slip system with optimum vanadium substitution at Bi-sites in Bi-2212 ceramic structure(Elsevier Science Sa, 2023) Ulgen, Asaf Tolga; Okur, Semih; Erdem, Umit; Terzioglu, Cabir; Turgay, Tahsin; Turkoz, Mustafa Burak; Yildirim, GurcanPresent study focuses extensively on the change in electrical, superconducting and microhardness parameters with partial substitution of trivalent V+3 impurities replacing Bi+3 ions in Bi-2212 ceramic compound with the aid of dc electrical resistivity and microhardness test measurements. Experimental findings, calculation results, and phenomenological discussions provide that the optimum vanadium substitution level is found to be x = 0.01 in the Bi2.0-xVxSr2.0Ca1.1Cu2.0Oy (Bi-2212) ceramic system for the highest conductivity, crystallinity quality, superconducting, and mechanical performance features depending on the decreased microscopic structural problems. All the findings are wholly verified by scanning electron microscopy (SEM) and X-Ray diffraction (XRD) analyses. The dc electrical measurements indicate that the optimum vanadium ions support the pairing mechanism for the formation of new polaronic states in the clusters of microdomains, and hence expand superconducting energy gap due to the enhancement of amplitude part of pair wave function in the spin-density wave systems. The excess vanadium content degrades all the basic thermodynamics and quantum mechanical quantities mentioned due to the stress-induced phase transformation. Numerically, the Bi-2212 advanced ceramic matrix prepared by the optimum vanadium impurity is noticed to present the smallest residual resistivity value of 0.08 m & omega; cm, room temperature resistivity value of 8.84 m & omega; cm, and broadening degree of 0.36 K. Similarly, the ceramic material is found to possess the highest residual resistivity ratio of 3.05, carrier concen-tration number of 0.153041, critical transition offset and onset value of 84.66 K and 85.02 K, respectively. Besides, the microhardness findings reveal that the same compound with the least sensitivity to the applied test loads exhibits the largest Hv value of 4.799 GPa, Young's moduli of 393.303 GPa, yield strength of (0.969 GPa), and elastic stiffness coefficient of 15.5574 (GPa)7/4 under the applied test load of 0.245 N. The XRD in-vestigations show that the presence of optimum vanadium impurity supports the formation of a high super-conducting phase, c-axis length, and average crystallite size. All the findings are morphologically confirmed by the SEM images. It is found that the crystallographically best crystallinity quality and view of surface morphology is observed for the optimum vanadium substitution level. All in all, new higher properties for the conductivity, crystallinity quality, surface morphology, superconducting, and microhardness parameters based on the optimum vanadium replacement encourage the Bi-2212 crystal system to use in much more application places.Öğe Evaluation of load-independent microhardness values in Plateau regions of Vanadium substituted Bi-2212 ceramics(Iop Publishing Ltd, 2022) Ulgen, Asaf Tolga; Okur, Semih; Erdem, Umit; Pakdil, Murat; Turgay, Tahsin; Yildirim, GurcanThis study reveals extensively effect of homovalent V/Bi partial replacement in Bi2.0-xVxSr2.0Ca1.1Cu2.0Oy ceramic matrix (0.00 <= x <= 0.30) on the key mechanical design performance parameters and load-independent Vickers microhardness parameters in plateau limit region by means of experimental microhardness tests and semi-empiric approaching models. It is found that the vanadium substitution level of x = 0.01 is observed to be optimum amount in the Bi-2212 crystal lattice for refinement of fundamental mechanical properties due to the enhancement in stabilization of durable tetragonal phase, surface residual compressive stress and elastic recovery mechanism. Conversely, from the replacement level of x = 0.01 onwards, the lattice strain field and stress concentration sites enhance significantly depending on the increase of microscopic structural problems, interaction problems between adjacent layers and crack-initiating flaws in Bi-2212 ceramic system. Correspondingly, stress-induced phase transformation begins to play predominant role, and excess vanadium substituted ceramic materials are easily broken at relatively smaller test load. Moreover, the models indicate that every ceramic compound shows standard indentation size effect (ISE) feature due to predominant behavior of elastic recovery in crystal structure. Hence, presence of optimum vanadium ions strengthens typical ISE characteristic behavior. Furthermore, among semi-empirical models the indentation-induced cracking (IIC) model exhibits the highest performance to inspect real microhardness values of Bi2.0-xVxSr2.0Ca1.1Cu2.0Oy ceramic compounds in the plateau limit region.Öğe Evolution of dynamics of physico-chemical and mechanical properties of hydroxyapatite with fluorine addition and degradation stability of new matrices(Elsevier, 2022) Erdem, Umit; Dogan, Deniz; Bozer, Buesra Moran; Karaboga, Seda; Turkoz, Mustafa Burak; Metin, Aysegul Ulku; Yildirim, GurcanThis multidisciplinary study examined sensitively the change in the dynamics of main mechanical performance, stability of crystal structure, crystallinity quality, strength, corrosion resistance, biocompatibility, resistance to structural degradation/separations and mechanical durability features of hydroxyapatite (HAp) biomedical materials based on the fluorine addition and degradation process to guide future medical and dental treatment studies. In the study, the fluorine ions were used to be the dental coating, filling and supporting material for biologically or synthetically produced bone minerals. The general characteristic properties were investigated by means of standard spectroscopic, structural and mechanical analysis methods including RAMAN, SEM-EDS, TEM, Vickers micro-indentation hardness and density measurements. A time dependent release test was performed to evaluate possible fluorine ion release after the degradation process. It was found that the fundamental charac-teristic properties of HAp biomedical materials are noted to improve with the increase in the fluoride level up to 2% due much more stabilization of HAp crystal system. The combination of RAMAN spectra and powder XRD analyzes indicates that 2% addition level affects positively the formation velocity of characteristic HAP phase. Besides, fluorine doped HAp materials all exhibited the main characteristic peaks after degradation process. This is attributed to the fact that the fluorine ions enabled the hydroxyapatite to enhance the structural quality and stability towards the corrosion environment. However, in case of excess dopant level of 3% the degradation rates were obtained to increase due to higher contribution rate and especially electrostatic interactions. As for the surface morphology examinations, 2% fluorine added HAp with the highest density of 3.0879 g/cm3 was determined to present the superior crystallinity quality (smallest grain size, best smooth surface, honeycomb pattern, regular shaped particles and densest particle distributions through the specimen surface). Conversely, the excess fluorine triggered to increase seriously degree of micro/macro porosity in the surface morphology and microscopic structural problems in the crystal system. Thus, the HAp doped with 3% was the most affected material from the degradation process. Additionally, the fluorine ion values read after the release process were quite far from the value that could cause toxic effects. Lastly, the optimum fluorine addition provides the positive effects on the highest durability, stiffness and mechanical fracture strength properties as a consequence of dif-ferentiation in the surface residual compressive stress regions (lattice strain fields), amplification sites and active operable slip systems in the matrix. Hence, the crack propagations prefer to proceed in the transcrystalline re-gions rather than the intergranular parts. Similarly, it was found that Vickers micro-indentation hardness tests showed that the microhardness parameters increased after the degradation process. All in all, the fluorine addition level of 2% was noted to be good choice to improve the fundamental characteristic properties of hy-droxyapatite biomedical materials for heavy-duty musculoskeletal, orthopedic implant, biological and thera-peutic applications in medicine and dentistry application fields.Öğe Evolution of operable slip systems, lattice strain fields and morphological view of Bi-2223 ceramic system with optimum NiO addition(Elsevier, 2023) Mercan, Ali; Kara, Emre; Dogan, Muhsin Ugur; Kaya, Senol; Terzioglu, Rifki; Erdem, Umit; Yildirim, GurcanThe current work extensively reveals the influence of different nickel oxide (NiO) impurity addition levels on the morphological, microstructural, key mechanical performance, and mechanical characteristic properties of Bi1.8Pb0.4Ca2.2Sr2Cu3Oy (Bi-2223) ceramics using scanning electron microscopy (SEM), powder X-ray diffraction (XRD), and Vickers micro-indentation (Hv) hardness measurements. It was observed that the addition of NiO impurity in the Bi-2223 crystal structure affected seriously the fundamental characteristic features. In the case of the optimum NiO concentration level of x = 0.1, the Bi-2223 materials exhibited the best crystallinity quality and coupling strengths between the adjacent layers, the most uniform surface view, and the densest, and the smoothest crystal structure. Similarly, the compound was noted to possess the hardest, highest mechanical strength, durable tetragonal phase, resistance toward failure by fatigue, and elastic recovery properties. Besides, it was observed that the characteristic Bi-2223 superconducting phase fraction and stabilization of the tetragonal crystal system reached the maximum level for the optimum concentration. Moreover, optimum NiO particles brought about a considerable increase in the number of operable slip systems, surface residual compressive force regions, and lattice strain fields. Correspondingly, the mobility of defects was blocked significantly depending on the preference of defects through transcrystalline regions. Additionally, optimum addition strengthened the typical indentation size effect due to the improvement of the recovery mechanism. In this regard, the NiO-added sample exhibited the least response to the applied loads. Thus, the Bi-2223 sample with the optimum NiO concentration was found to present the highest hardness parameter of 0.496 GPa, greatest elastic deformation value of 16.493 GPa, largest stiffness value of 1.044 MN/m, and smallest contact depth of 5.849 mu m. On the other hand, after the optimum concentration level of x = 0.1, there appeared serious increase in problems including internal defects, impurity residues, microscopic structural problems, and connection problems between the grains. All experimental findings were theoretically supported by semi-empirical mechanical methods. To sum up, the addition of NiO particles was noticed to increase the potential application areas of Bi-2223 ceramics.Öğe Evolution of residual compressive stress regions in Co-diffused Bi-2212 engineering ceramics with annealing temperature(Springer, 2024) Mercan, Ali; Erdem, Umit; Ulgen, Asaf Tolga; Gulen, Mahir; Turkoz, Mustafa Burak; Turgay, Tahsin; Yildirim, GurcanThe role of diffusion annealing temperatures intervals 600-850 degrees C on durable tetragonal phase, surface morphology, and main mechanical performance parameters of Co surface-layered Bi2.1Sr2.0Ca1.1Cu2.0Oy (Bi-2212) samples has extensively been examined by scanning electron microscopy (SEM), Electron Dispersive X-ray (EDX) technique and microindentation Vickers hardness (Hv) tests. The experimental findings have shown that every material prepared has presented different composition distributions on the specimen surface as a consequence of the successful production of materials. Besides, the mechanical characteristics and durable tetragonal phase have been noted to enhance significantly with the enhancement of annealing temperature up to 650 degrees C due to the formation of new slip systems, surface residual compressive stress regions, connections between grains, and chemical bonding between the foreign and host atoms. Further, the optimum temperature has led to the reduction in stored internal strain energy and degree of granularity in the Co-diffused Bi-2212 crystal system. In this respect, the sample with the least sensitive to the external forces has exhibited the highest elastic modulus of 0.5445 GPa, shear modulus of 17.8515 GPa, yield strength of 181.5 MPa, and resilience of 369.1 MPa under 0.295 N. Accordingly, the cracks and dislocations have preferred to propagate throughout the transcrystalline regions, and crack growth size was easily controlled. Similarly, the saturation limit region has begun at relatively higher applied test load magnitudes. Conversely, the excess annealing temperature has caused the increase in the agglomeration of cobalt ions throughout the intergranular regions. Correspondingly, the activation of stress-induced phase transformation has been triggered seriously. Bi-2212 ceramic compound exposed to the optimum diffusion annealing temperature exhibits the most uniform surface view and crystalline quality with the densest surface morphology and the largest particle distributions and orientations. Moreover, every material studied has perfectly presented the characteristic indentation size effect behavior. The examination of granularity degree depending on elasticity moduli has verified all the Hv test results and discussions. All in all, this study guides the use of engineering ceramics in more application areas due to the increase in their service life.Öğe Fabrication of mechanically advanced polydopamine decorated hydroxyapatite/polyvinyl alcohol bio-composite for biomedical applications: In-vitro physicochemical and biological evaluation(Elsevier, 2022) Erdem, Umit; Dogan, Deniz; Bozer, Busra M.; Turkoz, Mustafa B.; Yildirim, Gurcan; Metin, Aysegul U.In this study, polydopamine (PDA) coated hydroxyapatite (HA) reinforced polyvinyl alcohol (PVA) films were produced to be used in biomedical applications such as bone tissue regeneration. pDA is coated not only to prevent the agglomeration of HA when encountering interstitial fluids but also to strongly bind the PVA for the interaction between materials so that the mechanical performance becomes more stabilized. pDA was coated on the hydroxyapatite surface using a radical polymerization technique, and the reinforced PVA were produced with pDA-coated HA (pDA-HA/PVA) nanoparticles. Fundamental characteristic properties of pDA-HA/PVA nanocomposite films were examined by morphological/chemical (SEM-EDS), microstructural (XRD, Ft-IR, and Raman), thermodynamic (TGA and TM), mechanical performance (Vickers microhardness) and biological activity analysis (MTT, genotoxicity and antimicrobial efficacy investigations). Physicochemical analysis showed that all the samples studied exhibited homogeneous mineral distributions through the main structures. According to TGA, TMA and hardness tests, the new composite structure possessed higher mechanical properties than neat PVA. Further, pDA-HA/PVA nanocomposites exhibited high antibacterial capacities against Acinetobacter Baumannii (A.Baumannii), Staphylococcus aureus (S. aureus), and Streptococcus mutans (S.mutans). Moreover, the new nanocomposites were noted to present good biocompatibility for fibroblast (L929) cells and to support remarkably MCS cells. All in all, this comprehensive work shows that the thermo-mechanically improved pDA-HA/PVA films will increase the application fields of PVA in biomedical fields especially tooth-bone treatments for coating, filling, or occlusion purposes.Öğe Homovalent Ho/Bi substitution effect on characteristic properties of Bi-2212 superconducting ceramics(Springer, 2021) Erdem, UmitIn the current work, the effect of trivalent Ho/Bi partial replacement on the fundamental characteristic features such as the general crystallinity quality quantities, dc electrical resistivity, superconducting, degree of granularity, strength quality of intra- and inter-grain boundary couplings in the oxygen-deficit multi-layered perovskite-based Bi2.1Sr2.0Ca1.1Cu2.0Oy (Bi-2212) superconducting ceramics is examined by powder X-ray diffraction (XRD), temperature-dependent electrical resistivity (rho-T), and Archimedes water displacement methods. The polycrystalline Bi2.1-xHoxSr2.0Ca1.1Cu2.0Oy compounds are produced by the conventional ceramic method within the molecular ratio intervals 0.00 <= x <= 0.30. All the experimental findings show that the trivalent holmium (Ho3+) impurities are successfully substituted by the bismuth (Bi3+) particles in the Bi-2212 crystal system. Besides, the optimum holmium concentration for the bulk Bi-2212 superconducting ceramics is recorded to be x = 0.01. XRD results indicate that the Bi-2212 material prepared by the optimum Ho/Bi substitution possesses the maximum average crystallite size (60 nm), Bi-2223 superconducting phase volume fraction (33.48%), c-axis length (32.55 angstrom), and Lotgering index (0.48) parameters. In this respect, the best sample with particle distributions well linked each other has the maximum bulk density value of 6.04 g/cm(3) and minimum degree of granularity of 4.13%. It is obvious that the optimum (excess) Ho/Bi partial substitution supports the enhancement in the density (granular structure nature) of Bi-2212 compound. Moreover, dc electrical resistivity measurement results show that the optimum homovalent Ho/Bi partial substitution in the Bi-2212 superconducting matrix leads to increase the homogeneities in the oxidation state of superconducting grains and especially densities of active and effective electronic states (DOS) at Fermi energy level. To sum up, this study indicates that the optimum trivalent Ho/Bi partial substitution increases the usage of Bi-2212 superconducting materials in much more application fields.Öğe Hydroxyapatite-based nanoparticles as a coating material for the dentine surface: An antibacterial and toxicological effect(ELSEVIER SCI LTD, 2020) Erdem, Umit; Dogan, Mustafa; Metin, Aysegul U.; Baglar, Serdar; Turkoz, Mustafa B.; Turk, Mustafa; Nezir, SaffetIn this study, nano sized hydroxyapatite (nHAp) and Ag(I) doped hydroxyapatite (Ag-nHAp) particles were synthesized by the precipitation method and used as a coating material for remineralization on caries-affected dentine samples. Characterization studies of both the synthesized hydroxyapatite-based particles and the coated dentine samples were performed using instrumental techniques such as SEM and FFIR, and then toxicity and antibacterial properties were also evaluated. It was observed that dentine samples were effectively coated by both nHAp and Ag center dot nHAp particles which have no toxic effects. Furthermore, the costing of nano-hydroxyapatite on dentine samples positively contributed to the viability of L929 fibroblast cells and also provided an antibacterial effect against to bacteria such as S. mutants, C. albicans and E. coli bacteria that are most frequently caused caries in the teeth. While all type of bacteria was eliminated by the nHAp coated dentine samples at 24th, Ag-nHAp coated dentine samples removed to all bacteria type at 1st.Öğe Impacts Of High Voltage Electric Field (Hvef) Applications On Germination And Seedling Growth Of Seed (Triticum Aestivum L.) With Analysis By Fourier Transform Infrared (Ftir) Spectroscopy(Parlar Scientific Publications (P S P), 2018) Ince-Yilmaz, Ozlem; Erol, Taskin; Kara, Kamil; Dogan, Mustafa; Erdem, UmitWheat is an important widely grown cereal that its grains used worldwide as a staple food. In this study, germination and seedling growth characteristics of grains of Triticum aestivum, the most widely grown species of the genus, in response to HVEF applications were studied. Three different intensities (50, 100 and 200 kV/m) were applied for 1, 5 and 10 min durations. Germination percentages were not affected by treatments, while germination speeds were inhibited by high intensities at long durations. Maximum enhancement in seedling growth measures which were given as root and shoot lengths and dry weights was determined for 5 min 50 kV/m treatment, where increases in average seedling lengths and dry weights were 34.2 % and 26.1 %, respectively. 1 min durations of treatments were also highly improved seedling growth, particularly at root measures. ATR technique was used to analyze the roots and first foliage leafs of treated seeds at FTIR spectroscopy. FTIR results supported that HVEF treatment could be a useful tool for enhancement of wheat seedling growth in early stages of development.Öğe Improvement in deformation degree of Zr surface-layered Bi-2223 ceramics by diffusion annealing temperature(Elsevier Sci Ltd, 2023) Mercan, Ali; Terzioglu, Rifki; Dogan, Muhsin Ugur; Kaya, Senol; Erdem, Umit; Yildirim, Gurcan; Terzioglu, CabirThis study investigated the effects of different annealing temperatures (650 degrees C <= T <= 840 degrees C) on the surface morphological and mechanical performance properties of Zr surface-layered Bi-2223 materials with scanning electron microscopy (SEM) images, Vickers microhardness (Hv) measurements, and semi-empirical mechanical approaches. It was observed that the ceramic compound exposed to 650 degrees C annealing temperature exhibited the superior performance features due to the enhancement in the deformation degree. This is because the Zr ions behaved as the nucleation centers to prevent the propagations of cracks and dislocations throughout the main matrix depending on the decrease in the degree of granularity and distributions of crystal structure problems over a wider area. Similarly, the SEM pictures indicated that the diffusion mechanism increased the random distributions of the thinner plate-like granular structures (serving as nucleation centers), leading the decrease in the coupling problems between the grains. Among the materials, the highest surface densification was observed for the compound exposed to 650 degrees C. Namely, surface morphological analysis showed a strong correlation be-tween microstructure and mechanical performances. Further, the zirconium ions were found to decrease in the non-recoverable stress concentration sites, crack-initiating defects, and dislocations in the ceramic system. Accordingly, the sensitivity to the applied test load was noted to decrease dramatically. Shortly, crack growth size and velocity were observed to be more easily under control. Correspondingly, the Zr ions delayed consid-erably the beginning points of saturation limit (load-independent) regions for the bulk Bi-2223 superconducting materials. Additionally, the Zr ions led to the change in the mechanical characteristic behavior from typical indentation size effect to reverse indentation size effect. Lastly, the microindentation hardness measurements were semi-empirically analyzed by the different models. According to the comparison, Hays-Kendall mechanical model was noted to provide the closest parameters to the load-independent microhardness results.Öğe Improvement in organization of Cu-O coordination and super-electrons in Bi-2212 ceramic matrix with Ag/Sr partial substitution(Springer, 2024) Al Azzawi, Abdullah Nabel Salman; Turkoz, Mustafa Burak; Erdem, Umit; Yildirim, GurcanThis study rationalizes the reason for an increase in the electrical conductivity, crystal quality, surface morphology, and superconductive transition temperatures for Bi-2212 superconductors via scientific facts and discussions depending on replacing the optimum Ag/Sr sites in the system for the first time. Every experimental result and related calculations indicate the successful replacement of monovalent Ag+ ions for the divalent Sr2+ ions in the polycrystalline Bi-2212 structure. Moreover, it is observed that the bulk Bi-2212 ceramic prepared with a partial substitution level of x = 0.01 is observed to possess the highest electrical conductivity and superconductive transition temperatures of 84.68 K and 86.26 K for the Tcoffset\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{c}<^>{offset}$$\end{document} and Tconset\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{c}<^>{onset}$$\end{document}, respectively. Besides, in the case of the optimum replacement level, the Bi-2212 ceramic exhibits the most uniform and smoothest surface appearance, highest interactions between the grains, best microcrystal distributions/orientations, and largest average crystalline distribution along the crystal structure. In this regard, this study becomes a leader in broadening the application spectra including the heavy-industrial technologies, innovative, advanced engineering-related sectors, and large-scale application fields for Bi-2212 superconducting ceramics.Öğe La3+ and F- dual-doped multifunctional hydroxyapatite nanoparticles: Synthesis and characterization(Wiley, 2021) Erdem, Umit; Turkoz, Mustafa B.Hydroxyapatite (HA) co-doped with La3+ and F- ions were synthesized by the precipitation method and sintered at 1,100 degrees C for 1 hr. Samples were characterized by the standard experimental methods including the density, X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscopy (SEM) to investigate their microstructure, phase formation, and bonding characteristics in detail. Moreover, the materials produced were identified using the microhardness tests. It was observed that in the most of materials, the hydroxyapatite was found to be the main phase with a minor amount of beta-tricalcium phosphate (beta-TCP). Furthermore, the presence of fluoride and small amount of beta-TCP was verified with all the characteristic FTIR bands of hydroxyapatite for the majority of samples studied. The result in SEM evaluation is that the produced HA powders have less deformed, uniformly distributed, and regularly shaped particles. Here, the material density has changed towards a less dense state with the increasing rate of La doping, but statistically significant difference was not obtained (p, .1942 > .05) with increase of the F doping. A significant difference was obtained the microhardness values between La3+ and F- ions co-doped HA materials and pure HA (p [.0053] < .05). Accordingly, this study confirmed that since the La3+ and F- ions can potentially increase the efficacy of HA. According to the spectral, mechanical, and microstructure analysis result, this material can be as a good candidate product for use as an occluding material for dental application.Öğe La3+ and F? dual-doped multifunctional hydroxyapatite nanoparticles: Synthesis and characterization(John Wiley and Sons Inc, 2021) Erdem, Umit; Turkoz, Mustafa B.Hydroxyapatite (HA) co-doped with La3+ and F? ions were synthesized by the precipitation method and sintered at 1,100°C for 1 hr. Samples were characterized by the standard experimental methods including the density, X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscopy (SEM) to investigate their microstructure, phase formation, and bonding characteristics in detail. Moreover, the materials produced were identified using the microhardness tests. It was observed that in the most of materials, the hydroxyapatite was found to be the main phase with a minor amount of ?-tricalcium phosphate (?-TCP). Furthermore, the presence of fluoride and small amount of ?-TCP was verified with all the characteristic FTIR bands of hydroxyapatite for the majority of samples studied. The result in SEM evaluation is that the produced HA powders have less deformed, uniformly distributed, and regularly shaped particles. Here, the material density has changed towards a less dense state with the increasing rate of La doping, but statistically significant difference was not obtained (p,.1942 >.05) with increase of the F doping. A significant difference was obtained the microhardness values between La3+ and F? ions co-doped HA materials and pure HA (p [.0053] <.05). Accordingly, this study confirmed that since the La3+ and F? ions can potentially increase the efficacy of HA. According to the spectral, mechanical, and microstructure analysis result, this material can be as a good candidate product for use as an occluding material for dental application. © 2021 Wiley Periodicals LLC.Öğe Magnetically responsive chitosan-based nanoparticles for remediation of anionic dyes: Adsorption and magnetically triggered desorption(Elsevier Science Sa, 2022) Babacan, Taner; Dogan, Deniz; Erdem, Umit; Metin, Aysegul UlkuChitosan-based nanoparticles (PGMA/mCHT) were prepared for the adsorption of anionic Reactive Red 120 (RR120) and Indigo Carmine (IC). The morphology and characteristics were clarified by using SEM-EDX, XRD, VSM, and FTIR. The adsorption of RR120 and IC on PGMA/mCHT was carried out in a batch process to determine the influence of initial dye concentration (5-600 mg/L), initial pH (3-9), temperature (5, 25, 35, and 45 degrees C) and contact time. Under acidic conditions, higher adsorption efficiencies of the PGMA/mCHT nanoparticles due to intermolecular interactions of dye molecules between the protonated amine groups and the sulfonyl groups. Bi-solute adsorption was also investigated revealing between dye molecules has no competitive effect at the same initial concentration. The kinetic results of RR120 and IC adsorption onto PGMA/mCHT nanoparticles fit well to the pseudo-second-order model. The desorption of dye molecules from PGMA/mCHT nanoparticles was also studied using an alternating magnetic field which is caused the superior desorption behavior demonstrating the magnetic nanoparticles can be acted as a nanoheater.Öğe Preparation of a novel functionalized magnetic nanobiocomposite as a carrier for protein adsorption(TAYLOR & FRANCIS INC, 2020) Metin, Aysegul Ulku; Dogan, Mustafa; Erdem, Umit; Babacan, Taner; Gungunes, HakanThis study aims the synthesis of a novel functionalized magnetic nanocarrier based on xanthan gum biopolymer. Glycidyl methacrylate was grafted on xanthan gum chains by radical polymerization reaction using two types of initiators: ammonium persulfate and benzoyl peroxide. Characterization studies of the magnetic nanocarrier were performed using several instruments such as Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, Energy-Dispersive-X-Ray Spectroscopy, X-Ray Diffraction Spectroscopy, Transmission Electron Microscopy, Mossbauer Spectroscopy, and Vibrating Sample Magnetometer. According to the Vibrating Sample Magnetometer data and Mossbauer analysis, Fe atoms were incorporated successfully in the polymer chains in Fe3+ state and magnetic nanocarrier has super-paramagnetic behavior, respectively. Epoxy groups on magnetic nanoparticles were converted to carboxylic acid groups using iminodiacetic acid and then tested to usability as a carrier for immobilization of proteins such as albumin, lipase and cytochrome c. The adsorption of albumin and lipase on magnetic nanoparticles were pH-dependent while cytochrome c was immobilized in a wide range of pH value. The calculated maximum experimental immobilization capacity of magnetic nanoparticles was 65.10 mg g(-1), 62.0 mg g(-1) and 188.0 mg g(-1) for albumin, lipase and cytochrome c, respectively. Experimental data fitted to Langmuir isotherm better than Freundlich. The rate of cytochrome c adsorption followed the pseudo-second-order kinetic. Results showed that the functionalized magnetic nanoparticles can be effectively used as a carrier for protein separations, especially for cytochrome c. Moreover, the functionalized magnetic nanocarrier had high affinity to Cytochrome c protein even in multiple protein systems.Öğe Refinement of fundamental characteristic properties with homovalent Er/Y partial replacement of YBa2Cu3O7-y ceramic matrix(Elsevier Science Sa, 2021) Erdem, Umit; Turkoz, Mustafa B.; Yildirim, Gurcan; Zalaoglu, Yusuf; Nezir, SaffetIn the current work, the effect of partial substitution of Er-sites for the Y-sites in the bulk YBa2Cu3O7-y (YBCO) crystal system on the fundamental superconducting, electrical, crystallinity and structural morphology features is examined together with the reasons by means of powder X-ray diffraction (XRD), temperature-dependent electrical resistivity (rho-T), scanning electron microscopy (SEM), electron dispersive X-ray (EDX) investigations and deduced calculation parameters. All the experimental test results show that the erbium impurities are suc-cessfully substituted by the yttrium sites in the bulk Y-123 crystal system, confirmed by sensitively the EDX and rho-T measurement results. Moreover, it is found that all the fundamental characteristic quantities improve with the increment in the Er/Y partial substitution level up to the value of x = 0.03 beyond which the features tend to degrade dramatically. In this respect, the bulk Y1-xErxBa2Cu3O7-y ceramic compound prepared within the molar ratio of x = 0.03 crystallizes in the orthorhombic space group P-4/ mmm with a little distortion due to the refinement in the crystallinity quality, crystallite growth, oxygen ordering degree, scattering mechanism, intra and intergrain boundary couplings, grain alignment distributions and orientations. The XRD results show that the optimum erbium content enables to develop seriously the fundamental crystallographic features (lattice strain, lattice cell constants, crystallite size distribution, dislocation density ratio, oxygen concentrations in the unit cells) of Y-123 crystal structure. However, the excess Er/Y substitution leads to enhance considerably the systematic structural problems and inhomogeneous distribution of strains (formed by the structural defects) in the YBCO crystal structure. Thus, the phase transition from orthorhombic to tetragonal (structural O-T transition) crystal structure is observed. In fact, the XRD result displays that the trivalent Er3+ particles may partially be replaced by the divalent Cu2+ host atoms in the bulk Y-123 crystal structure after the critic substitution level of x = 0.03. The optimum Er concentration causes to form more thermodynamically activated super-electrons in the homogeneous superconducting cluster percentages in the paths due to the induced polaronic effect, and accordingly the intrinsic overdoped nature of Y-123 ceramic system transits into optimally doped state. Similarly, the erbium ions enable to increase the mobile hole carrier concentration and homogeneities in the oxidation state of superconducting grains. Namely, the amplitude of pair wave function (Psi=Psi(0)e(-i phi)) is strength enough to form bipolarons in the polarizable lattices and localize of densities of electronic states (DOS) at Fermi level. SEM investigations picture that the surface morphology view and crystallinity quality develop remarkably with the increment in the erbium content up to the critical dopant level of x = 0.03 where the sample exhibits the best grain alignment orientations, densest and smoothest surface morphology with the combination of lowest porous and largest particle distributions well linked each other. All in all, this comprehensive work based on the analysis of Er/Y partial replacement mechanism along the YBa2Cu3O7- y ceramic matrix may open up a newly/novel and feasible area for the advanced engineering, heavy-industrial technology and large-scale applications of type-II superconducting materials. (C) 2021 Elsevier B.V. All rights reserved.Öğe Refinement of fundamental characteristic properties with homovalent Er/Y partial replacement of YBa2Cu3O7?y ceramic matrix(Elsevier Ltd, 2021) Erdem, Umit; Turkoz, Mustafa B.; Yıldırım, Gurcan; Zalaoglu, Yusuf; Nezir, SaffetIn the current work, the effect of partial substitution of Er-sites for the Y-sites in the bulk YBa2Cu3O7?y (YBCO) crystal system on the fundamental superconducting, electrical, crystallinity and structural morphology features is examined together with the reasons by means of powder X-ray diffraction (XRD), temperature-dependent electrical resistivity (?-T), scanning electron microscopy (SEM), electron dispersive X-ray (EDX) investigations and deduced calculation parameters. All the experimental test results show that the erbium impurities are successfully substituted by the yttrium sites in the bulk Y-123 crystal system, confirmed by sensitively the EDX and ?-T measurement results. Moreover, it is found that all the fundamental characteristic quantities improve with the increment in the Er/Y partial substitution level up to the value of x = 0.03 beyond which the features tend to degrade dramatically. In this respect, the bulk Y1?xErxBa2Cu3O7?y ceramic compound prepared within the molar ratio of x = 0.03 crystallizes in the orthorhombic space group P4/mmm with a little distortion due to the refinement in the crystallinity quality, crystallite growth, oxygen ordering degree, scattering mechanism, intra and inter-grain boundary couplings, grain alignment distributions and orientations. The XRD results show that the optimum erbium content enables to develop seriously the fundamental crystallographic features (lattice strain, lattice cell constants, crystallite size distribution, dislocation density ratio, oxygen concentrations in the unit cells) of Y-123 crystal structure. However, the excess Er/Y substitution leads to enhance considerably the systematic structural problems and inhomogeneous distribution of strains (formed by the structural defects) in the YBCO crystal structure. Thus, the phase transition from orthorhombic to tetragonal (structural O–T transition) crystal structure is observed. In fact, the XRD result displays that the trivalent Er3+ particles may partially be replaced by the divalent Cu2+ host atoms in the bulk Y-123 crystal structure after the critic substitution level of x = 0.03. The optimum Er concentration causes to form more thermodynamically activated super-electrons in the homogeneous superconducting cluster percentages in the paths due to the induced polaronic effect, and accordingly the intrinsic overdoped nature of Y-123 ceramic system transits into optimally doped state. Similarly, the erbium ions enable to increase the mobile hole carrier concentration and homogeneities in the oxidation state of superconducting grains. Namely, the amplitude of pair wave function (? = ?0e-i?) is strength enough to form bipolarons in the polarizable lattices and localize of densities of electronic states (DOS) at Fermi level. SEM investigations picture that the surface morphology view and crystallinity quality develop remarkably with the increment in the erbium content up to the critical dopant level of x = 0.03 where the sample exhibits the best grain alignment orientations, densest and smoothest surface morphology with the combination of lowest porous and largest particle distributions well linked each other. All in all, this comprehensive work based on the analysis of Er/Y partial replacement mechanism along the YBa2Cu3O7?y ceramic matrix may open up a newly/novel and feasible area for the advanced engineering, heavy-industrial technology and large-scale applications of type-II superconducting materials. © 2021 Elsevier B.V.
