Yazar "Elbuken, Caglar" seçeneğine göre listele

Listeleniyor 1 - 6 / 6
  • Küçük Resim
    Öğe
    Focusing-free impedimetric differentiation of red blood cells and leukemia cells: A system optimization
    (ELSEVIER SCIENCE SA, 2020) Bilican, Ismail; Guler, Mustafa Tahsin; Serhatlioglu, Murat; Kirindi, Talip; Elbuken, Caglar
    A focusing-free microfluidic impedimetric cell detection system is developed. The effect of the channel dimensions, solution conductivity, excitation voltage, and particle size on impedimetric signal outputs were optimized to increase the sensitivity of the system. Conventional microfabrication techniques were adapted to obtain low height, resealable microchannels. The geometry optimization was performed by a combination of analytical, numerical and experimental approaches. The results demonstrate that reliable impedimetric particle differentiation can be achieved without any labeling or particle focusing. The system parameters were studied and rule-of-thumb design criteria were provided. Finally, using the developed system, red blood cells and leukemia cells were experimentally detected and differentiated. Thanks to its simplicity, the focusing-free cell differentiation system may find applications in several cellular diagnostic uses.
  • Küçük Resim
    Öğe
    Impedance-based viscoelastic flow cytometry
    (Wiley, 2019) Serhatlioglu, Murat; Asghari, Mohammad; Guler, Mustafa Tahsin; Elbuken, Caglar
    Elastic nature of the viscoelastic fluids induces lateral migration of particles into a single streamline and can be used by microfluidic based flow cytometry devices. In this study, we investigated focusing efficiency of polyethylene oxide based viscoelastic solutions at varying ionic concentration to demonstrate their use in impedimetric particle characterization systems. Rheological properties of the viscoelastic fluid and particle focusing performance are not affected by ionic concentration. We investigated the viscoelastic focusing dynamics using polystyrene (PS) beads and human red blood cells (RBCs) suspended in the viscoelastic fluid. Elasto-inertial focusing of PS beads was achieved with the combination of inertial and viscoelastic effects. RBCs were aligned along the channel centerline in parachute shape which yielded consistent impedimetric signals. We compared our impedance-based microfluidic flow cytometry results for RBCs and PS beads by analyzing particle transit time and peak amplitude at varying viscoelastic focusing conditions obtained at different flow rates. We showed that single orientation, single train focusing of nonspherical RBCs can be achieved with polyethylene oxide based viscoelastic solution that has been shown to be a good candidate as a carrier fluid for impedance cytometry.
  • Küçük Resim
    Öğe
    Rapid fabrication of microfluidic PDMS devices from reusable PDMS molds using laser ablation
    (Iop Publishing Ltd, 2016) Isiksacan, Ziya; Guler, M. Tahsin; Aydogdu, Berkan; Bilican, Ismail; Elbuken, Caglar
    The conventional fabrication methods for microfluidic devices require cleanroom processes that are costly and time-consuming We present a novel, facile, and low-cost method for rapid fabrication of polydimethylsiloxane (PDMS) molds and devices. The method consists of three main fabrication steps: female mold (FM), male mold (MM), and chip fabrication. We use a CO, laser cutter to pattern a thin, spin -coated PDMS layer for FM fabrication. We then obtain reusable PDMS MM from the FM using PDMS/PDMS casting. Finally, a second casting step is used to replicate PDMS devices from the MM. Demolding of one PDMS layer from another is carried out without any potentially hazardous chemical surface treatment. We have successfully demonstrated that this novel method allows fabrication of microfluidic molds and devices with precise dimensions (thickness, width, length) using a single material, PDMS, which is very common across microfluidic laboratories. The whole process, from idea to device testing, can be completed in 1.5 h in a standard laboratory.
  • Küçük Resim
    Öğe
    A simple approach for the fabrication of 3D microelectrodes for impedimetric sensing
    (Iop Publishing Ltd, 2015) Guler, Mustafa Tahsin; Bilican, Ismail; Agan, Sedat; Elbuken, Caglar
    In this paper, we present a very simple method to fabricate three-dimensional (3D) microelectrodes integrated with microfluidic devices. We form the electrodes by etching a microwire placed across a microchannel. For precise control of the electrode spacing, we employ a hydrodynamic focusing microfluidic device and control the width of the etching solution stream. The focused widths of the etchant solution and the etching time determine the gap formed between the electrodes. Using the same microfluidic device, we can fabricate integrated 3D electrodes with different electrode gaps. We have demonstrated the functionality of these electrodes using an impedimetric particle counting setup. Using 3D microelectrodes with a diameter of 25 mu m, we have detected 6 mu m-diameter polystyrene beads in a buffer solution as well as erythrocytes in a PBS solution. We study the effect of electrode spacing on the signal-to-noise ratio of the impedance signal and we demonstrate that the smaller the electrode spacing the higher the signal obtained from a single microparticle. The sample stream is introduced to the system using the same hydrodynamic focusing device, which ensures the alignment of the sample in between the electrodes. Utilising a 3D hydrodynamic focusing approach, we force all the particles to go through the sensing region of the electrodes. This fabrication scheme not only provides a very low-cost and easy method for rapid prototyping, but which can also be used for applications requiring 3D electric field focused through a narrow section of the microchannel.
  • Küçük Resim
    Öğe
    Tape'n roll inertial microfluidics
    (Elsevier Science Sa, 2019) Asghari, Mohammad; Serhatlioglu, Murat; Saritas, Resul; Guler, Mustafa Tahsin; Elbuken, Caglar
    Particle focusing and separation in microfluidic devices are critical for biological and medical applications. Inertial microfluidics is used for high throughput bio-particle focusing and separation. Most of the inertial microfluidic systems use planar structures for squeezing the particles in streams. Particle manipulation in 3D structures is often overlooked due to the complexity of the fabrication. In this study, we introduce some novel microchannel designs for inertial microfluidics by using a simple fabrication method that allows construction of both 2D and 3D structures. First, inertial migration of particles in 2D layouts including straight, spiral, and square spiral channels is investigated. Afterward, by applying a "tape'n roll" method, helical and double oriented spiral channels are configured and unexplored inertial migration behaviours are observed. Thanks to the simplicity of the fabrication and the unique characteristics of the new designs, high performance microfluidic inertial migration results can be obtained without any need for complicated microfabrication steps. The design optimization cycle can also be shortened using a computational approach we introduce in this study. (C) 2019 Elsevier B.V. All rights reserved.
  • Küçük Resim
    Öğe
    A versatile plug microvalve for microfluidic applications
    (Elsevier Science Sa, 2017) Guler, M. Tahsin; Beyazkilic, Pinar; Elbuken, Caglar
    Most of the available microvalves include complicated fabrication steps and multiple materials. We present a microvalve which is inspired from macroplug valves. The plug microvalve is fabricated by boring a hole through a rigid cylindrical rod and inserting it through a microfluidic chip. It simply functions by rotating the rod which aligns or misaligns the valve port with the microchannel. The rod is made up of a rigid material for applying the valve to an elastic polydimethylsiloxane (PDMS) microchannel. The valve can also be used for a rigid channel by inserting the rod into an elastic tubing. Therefore, the presented microvalve can be used for both elastomeric and thermoplastic channels. The plug microvalve can be applied to a prefabricated microchannel and does not require modification of the mold design. We have verified the repeatability and robustness of the valve by repetitive operation cycles using a servo motor. The plug microvalve is adaptable to numerous microfluidic applications. We have shown three modes of operation for the microvalve including fluid flow control across multiple intersecting channels. Integrating the microvalve to some commonly used microfluidic designs, we demonstrated the versatility and the practicality of the microvalve for controlling flow focusing, microdroplet sorting and rapid chemical agent detection. This low-cost microvalve significantly minimizes the prototyping time for microfluidic systems. (C) 2017 Elsevier B.V. All rights reserved.